很多参数,不知道怎么设置(我的qte是3.3.4的)
我的开发板是arm结构
(在qtopia及dt2目录下的mkspecs里都没有看到arm-linux-g++或linux-arm-g++目录)
Usage: configure [-qte 'cfg'] [-qpe 'cfg'] [-libpath path] [-prefix path]
[-debug] [-qtopiadesktop] [-dprefix path]
[-qt2 'cfg'] [-dqt 'cfg']
-qte cfg ....... Specifies the configuration to use for building
Qt/Embedded. For a full description of all possible Qt
configuration options type:
/work/qtopia-free-2.2.0/qt2/configure -help
or read the getting started section in the online
reference manual which can be found at:
/work/qtopia-free-2.2.0/qtopia/doc/html/index.html
For your convenience you can also use one of the following shortcuts as the cfg value which will then be replaced
with the full configuration listed after the shortcut:
keypad '-embedded -no-xft -qconfig qpe -qvfb -depths 4,8,16,32 -keypad-mode -system-jpeg -gif'
arm-keypad '-embedded -no-xft -xplatform linux-sharp-g++ -qconfig qpe-keypad-mode -depths 16,32 -no-qvfb -system-jpeg -gif'
no-keypad '-embedded -no-xft -qconfig qpe -qvfb -depths 4,8,16,32 -system-jpeg -gif -D QT_TRANSFORM_VFB'
arm-no-keypad '-embedded -no-xft -xplatform linux-sharp-g++ -qconfig qpe-depths 16,32 -no-qvfb -system-jpeg -gif'
-qpe cfg ....... Specifies the configuration to use for building Qtopia.
For a full description of all possible Qtopia
configuration options type:
/work/qtopia-free-2.2.0/qtopia/configure -help
or read the getting started section in the online
reference manual which can be found at:
/work/qtopia-free-2.2.0/qtopia/doc/html/index.html
For your convenience you can also use one of the following shortcuts as the cfg value which will then be replaced
with the full configuration listed after the shortcut:
phone '-edition phone -displaysize 176x208'
arm-phone '-xplatform linux-sharp-g++ -edition phone -displaysize 176x208'
pda '-edition pda -displaysize 240x320'
arm-pda '-xplatform linux-sharp-g++ -edition pda -displaysize 240x320'
core '-edition core -displaysize 240x320'
arm-core '-xplatform linux-sharp-g++ -edition core -displaysize 240x320'
-libpath path .. Adds an extra path to the Qtopia configuration from which
extra libraries may be included. For example, if
path=foobar then the following will be appended to the qpe configuration: -L 'foobar' -R 'foobar'
-prefix path ... Install Qtopia into path instead of
/work/qtopia-free-2.2.0/qtopia/image/opt/Qtopia. (1)
-debug ......... Build in debug mode. This affects Qt/Embedded, Qtopia and
(if Qtopia Desktop is being built) Qt 3. (2)
-qtopiadesktop . Enable Qtopia Desktop (the desktop PC companion program
that allows you to synchronise data). (1)
-dprefix path .. Install Qtopia Desktop into path instead of
/work/qtopia-free-2.2.0/qtopia/dimage/opt/Qtopia. (1)
-qt2 cfg ....... Specifies the configuration to use when building Qt 2
(tools package).
-dqt cfg ....... Specifies the configuration to use for building Qt 3
(tools package).
IMPORTANT: Please ensure that you quote configuration arguments to -qte,
-qpe, -qt2 and -dqt so that your shell does not split the
arguments.
NOTE: Depending on the source package not all listed configurations may be
possible.
(1) NOTE: The presence of these options in a -qpe parameter overrides the
configure arguments.
(2) NOTE: Any -debug or -release arguments in qte/qte (and dqt if Qtopia
Desktop is enabled) arguments will be ignored and this value used
instead.
[ 此贴被XChinux在2006-04-14 23:46重新编辑 ]
